Cu－Zn－Al合金中贝氏体的有序性

本文用Ｘ射线研究了Ｃｕ－２０Ｚｎ－６Ａｌ（ｗｔ％）合金中贝氏体结构的有序性，并与马氏体结构进行了比较，实验表明，从高温Ｂ２母相和低温Ｌ２１母相生成的贝氏体中（１１５）和（２０５）衍射峰或（１２１０）和（２０１０）衍射峰是重叠的，对生成的贝氏体进行一段时间的保温或缓慢冷却处理，其衍射峰的特征并不改变，这与马氏体（１１５）和（２０５）衍射峰或（１２１０）和（２０１０）衍射峰的分离特性不相符合。说明贝氏体结构有序度与马氏体明显不同，它的形成不可能继承母相的有序度。     

机械研磨 Ni_(50)B_(50)合金形成非晶的过程

本文研究了机械研磨 Ni_(50)B_(50)合金非晶的形成过程。唯象地提出用 J-M-A 方程描述此过程,并作了简单的讨论。     

Stored energy analysis of Zn—5Al eutectic alloy in superplastic deformation

The stored energy and the energy release during SPD(superplastic deformation)of a Zn-5Al alloy were studied.The alloy after rolling process gains more stored energy,and the as-rolled speciment can obtain maximum elongation and minimum flow stress without hot loding treatment before SPD.Experimental results show that stroed energy release process is along with SPD process and is also an impetus to SPD.The as -rolled Zn-5Al alloy has 48J/mol stored energy which was measured with DSC(differential scanning calorimeter)and conforms well to the calcuated value.The as-rolled Zn-5Al alloy after SPD with an elongation of 2500% releases 112J/mol stored energy,Analysis shows that the strain rate is in direct ratio to the rate of stred energy release.     

机械合金化Zr-Al-Ni-Cu-Ag非晶合金的晶化行为

研究了机械合金化非晶态Zr65Al7.5Ni10Cu7.5Ag10合金的晶化过程，由于存在扩散不均匀区，机械合金化非晶合金在深过冷液相区的退火组织不同于快淬合金，在深过冷液相区退火，析出二十面体准晶相及一些知相：在靠近第一个放热峰的温度退火，近出Zr2Cu相：第二个放热峰对应残余非晶相及准晶相向Zr2Ni,Zr2-Al3的转变。     

铝活塞余热淬火和自然时效的应用研究

图 1所示的活塞试件 ,在开型时间为 5 0s～ 5 5s时 ,其表面温度为 (4 90± 5 )℃ ,可满足淬火要求。自然时效时间为 2 4天时 ,其机械性能可达到国标技术要求。这种新工艺有明显的经济效益。     

非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经预退火后的晶化动力学的DTA研究

研究了非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经400℃，保温10min预退火后的晶化动力学。结果表明；该合金的晶化相为α-Fe固溶体和Sm2Fe17Cx金属间化合物，两相的晶化表观激活能分别为557KJ/mol和514KJ/mol，当晶化体积分数为60%时，α-Fe相的晶化激活能达极大值；Sm2Fe17Cx相晶化激活能则随其晶化体积分数的增加而逐渐减小。     

压力对Fe－29wt％Ni合金超细微粒特性的影响

利用蒸发冷凝法，制备了不同平均粒径的Ｆｅ－２９ｗｔ％Ｎｉ合金超细微粒。在不同压强下，将超细微粒压制成片。随压强增大，马氏体体积分数和比饱和磁化强度σｓ明显增大，而矫顽力Ｈｃ呈线性下降。压力效应与平均粒径ｄ大小密切相关     

Direct electroless Ni-P deposition on AM50 magnesium alloy from sulfate bath

A bright electroless Ni-P deposition on AM50 magnesium alloy in a sulfate plating bath was proposed by using direct plating process with non-chromate pretreatment. The electroless Ni-P plating on AM50 magnesium alloy has an admirable appearance and good adhesion. The results indicate that the electroless Ni-P deposition with non-chromate pretreatment has better adhesion than that of zinc immersion coating. Anodic polarization curves indicate that the electroless Ni-P deposition obtained from the sulfate bath has similar corrosion-resistance to that obtained from basic nickel carbonate bath. The deposition process generates less pollutant by a non-chromate plating bath and is suitable for the magnesium alloys manufacture because of its low cost. The hardness of the electroless Ni-P plated AM50 is about HV 720.6 and HV 969.7 after heat treatments at 180℃ for 2 h. The wear resistance of Ni-P plated magnesium alloy specimens is about 5 to 9 times as high as that of bare magnesium alloys.     

热强钛合金BT25组织与性能

介绍了前苏联航空发动机用热强钛合金（或高温钛合金）BT25的发展概况，并对BT25合金的成分特点、热处理强化优点等做了进一步阐述，给出了退火状态下的物理性能，在说明热强钛合金微观组织与力学性能关系的基础上给出了BT25合金的各种力学性能。     

Homogeneous Plastic Flow of Fully Amorphous and Partially Crystallized Zr_(41.2)Ti_(13.8)Cu_(12.5)Ni_(10)Be_(22.5) Bulk Metallic Glass

The homogeneous plastic flow of fully amorphous and partially crystallized Zr(41.2)Ti(13.8)Cu(12.5)Ni(10)Be(22.5) bulk metallic glass (Vitl) has been investigated by compression tests at high temperatures in supercooled liquid region. Experimental results show that at sufficiently low strain rates, the supercooled liquid of the fully amorphous alloy reveals Newtonian flow with a linear relationship between the flow stress and strain rate. As the strain rate is increased, a transition from linear Newtonian to nonlinear flow is detected, which can be explained by the transition state theory. Over the entire strain rate interval investigated, however, only nonlinear flow is present in the partially crystallized alloy, and the flow stress for each strain rate is much higher. It is found that the strain rate-stress relationship for the partially crystaltized alloy at the given temperature of 646 K also obeys the sinh law derived from the transition state theory, similar to that of the initial homogeneous amo